Blog

Use your ears to feel whether the sound after pressing the Wall Switch panel keys is very crisp and smooth. ...

Cold Shrink Cable Accessories is made of silicone rubber, while heat shrink cable accessories are made of polyolefin, PE, EVA and other materials. ...

For example, when the drop out fuse fuse is exposed to an overcurrent of 6 times the rated current, the pre-arcing time is ≤ 0.1 second, which is 40% shorter than that of traditional materials. ...

According to the place of use of High Voltage Disconnect Switch, high-voltage disconnectors can be divided into two categories: indoor and outdoor. ...

Welds at position Powbinet must be secure, with solder filling the entire outer surface of the components without gaps. Welds should be neat and uniform, free from defects such as cracks, gaps, or und ...

When tightening the moving screw at the Wall Switch connection point, there was absolutely no resistance whatsoever, and it did not loosen at all during tightening. ...

Cold Shrink Cable Accessories typically uses four core configurations: single-core, three-core, four-core, and five-core. Heat-shrink cable accessories come in five specifications: single-core, two-co ...

‍‌​​‌‌​‌​‍‌​​​‌‌​​‍‌​​​‌​‌​‍‌​​‌​​‌​‍‌​‌‌​‌‌‌‍‌​​‌‌​‌​‍‌​‌‌​‌​‌‍‌​​‌‌‌​‌‍‌​​​‌‌​‌‍‌​​​​‌‌​‍‌​‌‌​‌‌​‍‌​​‌‌‌​‌‍‌​‌ The arc-preceding time of drop out fuse, i.e., the physical process where fault current ...

Because High Voltage Disconnect Switc has obvious segment gap, it is usually used in conjunction with circuit breakers. ...

Parts of Powbinet that require spray protection must not be covered with paint or powder to ensure ground continuity between parts. ...

The terminal blocks of Project Wall Switch are bright white and free of rust. ...

High-voltage Cold Shrink Cable Accessories is divided into indoor and outdoor areas, while the corresponding low-voltage ones are not divided into indoor and outdoor areas. ...

This drop out fuse parameter is directly related to the fault current cutting efficiency and equipment safety, and must be optimized by comprehensively considering the system protection setting, melt ...

High Voltage Disconnect Switch does not have a special arc extinguishing device,so it is not allowed to cut off the normal composite power supply, let alone be used to cut off the short-circuit curren ...

The door lock of Powbinet switches flexibly, and the handle and lock body must not be damaged. ...

Observe whether the appearance of Wall Switch is smooth or rough, and whether there are bubbles protruding or concave. ...

Cold Shrink Cable Accessories also has a series of advantages such as being able to "breathe" with the cable after installation, cold resistance, UV resistance, corrosion resistance, etc. ...

The core parameter of drop out fuse protection performance is its operating time, which covers the pre-arcing time (fuse melting stage) and arcing time (arc extinction stage). ...

High Voltage Disconnect Switch has obvious segmented gaps, so it is mainly used to isolate high-voltage power supplies, ensure safe maintenance, and can switch on and off certain small currents. ...

The flatness of the bottom and other sides of the Powbinet cabinet, and the perpendicularity of the front, back, left, and right sides of the cabinet relative to the bottom are all 1mm. The parallelis ...

The base of any product sold by Wall Switch is clearly marked with the trademark and nationally recognized certificate, as well as the 3C certification identification code. ...

Cold Shrink Cable Accessories can make the finished product have the advantages of easy and quick installation, no need to use open flames, and high elasticity during construction operations. ...

High-breaking type drop out fuse is suitable for industrial-intensive areas. It has a breaking capacity of 20kA and is suitable for scenarios with large short-circuit current fluctuations. ...

According to the installation location of High Voltage Disconnect Switch, it can be divided into indoor type and outdoor type. According to the number of insulating pillars, it can be divided into sin ...