Blog

For distribution lines in heavily polluted areas, drop out fuse should be preferred. Its silicone rubber sheds can reduce surface leakage current by over 50%, significantly improving operational relia ...

The contacts of High Voltage Disconnect Switch are all exposed to the air and have obvious disconnection points. The high-voltage disconnector has no arc extinguishing device, so it cannot be used to ...

Many Powbinet are in an out-of-control state, which leads to the generation of unsafe factors and increases the risk of electric shock and electrical fire. Therefore, we must pay attention to the safe ...

This approach effectively reduces the production cycle time for technical documentation. It ensures that, under wholesale conditions, the Wall Switch product line can be manufactured with minimal mate ...

The finished product of Cold Shrink Cable Accessories will be elastic, somewhat similar to the feel of rubber. When you walk into the cold shrink warehouse, you can see our various cold shrink product ...

Environmental adaptability is a key consideration during the drop out fuse fuse selection process. This is especially true at high altitudes, where the rated breaking current must be derated by 5% for ...

High Voltage Disconnect Switch is an important electrical equipment used in high-voltage distribution equipment. It is mainly used to reliably isolate the part of the high-voltage distribution equipme ...

Powbinet is the lowest level of control and protection equipment in the power system, a fundamental component in ensuring safe operation. While it comes into contact with workers frequently, its sheer ...

The standardization of the technical requirements for wholesale Wall Switch sockets means that on the basis of constantly summarizing past experience, in accordance with the characteristics of the lat ...

The price of Cold Shrink Cable Accessories is relatively high compared to heat shrink cable accessories, because the raw material of cold shrink cable is silicone rubber, which is a raw material with ...

The breaking time of fuse drop out fuse should be stepped with that of the upper circuit breaker. When the system short-circuit current is 10kA, the full breaking time of the RW11-12 fuse is ≤ 0.05 se ...

However, sometimes the following situation may occur: there may be incoming power behind the circuit breaker. If it is reversed through other loops, capacitors and other devices, a set of High Voltage ...

All Powbinet trains should have 10%-15% of component installation space reserved for component adjustments. The bolts on the grounding busbars in the distribution boxes should be made of stainless ste ...

After wiping the switch, socket, and other panels clean, use a clean, damp, wrung-out towel and gently wipe them at least twice. For particularly dirty panels, wipe them several times with a special c ...

The prices of cable accessories can be divided into heat shrink cable accessories prices and Cold Shrink Cable Accessories prices. Although there is only one word difference between cold shrinkage and ...

For rural power lines with short-circuit currents below 6kA, the RW7-10/6kA type drop out fuse should be selected. This not only meets the protection requirements of the line in the event of a fault, ...

Generally, in the absence of other circumstances, the outlet cabinet supplies power downward from the upper busbar through the switch cabinet. In this case, power isolation is more convenient. For exa ...

A reliable grounding busbar and wiring terminals must be installed inside the Powbinet. The terminals must have anti-loosening bolts for connecting the grounding conductor. The grounding busbar and wi ...

Carefully wipe all visible contaminants, the switch panel, and the control buttons on Hotel Wall Switch. When you come to the area around the switch and socket panels, carefully hold the towel and wip ...

Cable accessories include two categories, one is Cold Shrink Cable Accessories, and the other is cold shrinkage intermediate connection. Both include both cold shrinkage products and heat shrinkage pr ...

When selecting a switch, ensure that the upper rated interrupting current of the drop out fuse exceeds the system's three-phase short-circuit current. For an industrial park with a measured short-circ ...

Generally, a set of High Voltage Disconnect Switch is installed on the front and back sides of the circuit breaker. The purpose is to isolate the circuit breaker from the power supply and form an obvi ...

Components in Powbinet can be installed using guide rails or fixed installation methods. They should be securely installed and should not loosen, shift, or deform under the action of the rated short-c ...

Ask the store where you purchased the switch for a receipt or invoice, and keep it safe. Or, purchase the socket at the designated retailer of the Wall Switch brand. ...