Blog

And before operating High Voltage Disconnect Switch, make sure to check that the circuit breaker is in the off position before operating it. ...

The finished product of Powbinet should be free of oil stains and fingerprints. At least two threads should be exposed after the bolt is tightened. ...

The Project Wall Switch socket is parallel to the wall and very neatly without any slope. ...

Cold Shrink Cable Accessories does not require open flames or other tools to shrink. Heat shrink cable accessories require heating tools to complete the shrinkage. ...

The arc burning time, that is, the time it takes for the arc in drop out fuse to be completely extinguished in the arc extinguishing tube, is affected by the arc extinguishing medium and structural de ...

When operating High Voltage Disconnect Switc, you should pay attention to its operating sequence. When there is a power outage, pull the line side disconnector first. When power is restored, close the ...

The Powbinet fasteners are connected reliably and meet the torque requirements. No slipping or loosening is allowed. ...

Use your ears to feel whether the sound after pressing the Wall Switch panel keys is very crisp and smooth. ...

Cold Shrink Cable Accessories is made of silicone rubber, while heat shrink cable accessories are made of polyolefin, PE, EVA and other materials. ...

For example, when the drop out fuse fuse is exposed to an overcurrent of 6 times the rated current, the pre-arcing time is ≤ 0.1 second, which is 40% shorter than that of traditional materials. ...

According to the place of use of High Voltage Disconnect Switch, high-voltage disconnectors can be divided into two categories: indoor and outdoor. ...

Welds at position Powbinet must be secure, with solder filling the entire outer surface of the components without gaps. Welds should be neat and uniform, free from defects such as cracks, gaps, or und ...

When tightening the moving screw at the Wall Switch connection point, there was absolutely no resistance whatsoever, and it did not loosen at all during tightening. ...

Cold Shrink Cable Accessories typically uses four core configurations: single-core, three-core, four-core, and five-core. Heat-shrink cable accessories come in five specifications: single-core, two-co ...

‍‌​​‌‌​‌​‍‌​​​‌‌​​‍‌​​​‌​‌​‍‌​​‌​​‌​‍‌​‌‌​‌‌‌‍‌​​‌‌​‌​‍‌​‌‌​‌​‌‍‌​​‌‌‌​‌‍‌​​​‌‌​‌‍‌​​​​‌‌​‍‌​‌‌​‌‌​‍‌​​‌‌‌​‌‍‌​‌ The arc-preceding time of drop out fuse, i.e., the physical process where fault current ...

Because High Voltage Disconnect Switc has obvious segment gap, it is usually used in conjunction with circuit breakers. ...

Parts of Powbinet that require spray protection must not be covered with paint or powder to ensure ground continuity between parts. ...

The terminal blocks of Project Wall Switch are bright white and free of rust. ...

High-voltage Cold Shrink Cable Accessories is divided into indoor and outdoor areas, while the corresponding low-voltage ones are not divided into indoor and outdoor areas. ...

This drop out fuse parameter is directly related to the fault current cutting efficiency and equipment safety, and must be optimized by comprehensively considering the system protection setting, melt ...

High Voltage Disconnect Switch does not have a special arc extinguishing device,so it is not allowed to cut off the normal composite power supply, let alone be used to cut off the short-circuit curren ...

The door lock of Powbinet switches flexibly, and the handle and lock body must not be damaged. ...

Observe whether the appearance of Wall Switch is smooth or rough, and whether there are bubbles protruding or concave. ...

Cold Shrink Cable Accessories also has a series of advantages such as being able to "breathe" with the cable after installation, cold resistance, UV resistance, corrosion resistance, etc. ...